Industrial Yarn Spin Finish: A Guide for Tire Cord, HMLS and High-Strength Yarn
An industrial yarn spin finish controls friction on guides and godets, holds filaments together and carries the yarn through drawing and heat setting. This guide covers the finishes Suretop makes for tire cord, HMLS, safety belt, airbag and high-strength yarns.
Ask for a finish recommendation
- Founded
- 2012
- Annual capacity
- 100,000 tons
- Transport package
- 200 L / 1,000 L drums
What an Industrial Yarn Spin Finish Does on a High-Tenacity Filament Line
An industrial yarn spin finish is the oil applied to the filaments during spinning, and its work is mechanical before it is chemical. It lowers friction where the yarn touches guides, godets and rollers so the filaments are not abraded at speed. It holds the filament bundle together through drawing and protects the surface through heat setting. A finish also carries static away and lets the yarn unwind from the package without snatching. Which type fits a high-tenacity filament process depends on the polymer, the spinning speed and what the yarn meets downstream.
An industrial yarn finish and a spin finish are the same oil, applied at the same point of filament spinning; the names are used interchangeably. The oil has to deliver lubricity between filament and metal, cohesion inside the bundle, control of static and even unwinding from the package. How much of each property a yarn needs is set by the fiber, the drawing conditions and the next process step. Suretop develops and adjusts formulations to the customer’s fiber type, spinning process and technical requirements, and supplies samples for testing and trial production.
Suretop is a manufacturer of spin finish oils for polyester, nylon, spandex and aramid fibers, based in Xiaoshan, Hangzhou, Zhejiang, China, and was founded in 2012. The plant sits near the Qiantang River on a site of 12,000 m², with an annual production capacity of 100,000 tons of chemical fiber spin finish. The range covers finishes for POY, FDY, DTY and industrial filament yarn production, and the company researches, develops, produces and sells surfactants and chemical fiber spin finishes.
The industrial-yarn items on this page are SLT-2235 Polyester Industrial Yarn Spin Finish (Safety Belt), SLT-2237 Polyester Industrial Yarn Spin Finish (HMLS), SLT-60 Industrial Yarn Spin Finish for Nylon Cord (Tire Cord), SLT-70 Polyamide Industrial Yarn Spin Finish (Airbag Yarn), SLT-80 Industrial Yarn Spin Finish for Nylon 66 (High-Strength Yarn), SLT-100 Nylon Industrial Yarn Oil and SLT-101 Polyamide Industrial Yarn Oil (High-Strength Yarn). For a recommendation, send the fiber type and process details through the inquiry form.
Industrial yarn spin finish models and specifications
| Parameter | Value |
|---|---|
| Appearance (at 30℃) | Yellow transparent liquid |
| Oil Content (%) | 98±1.0 |
| pH Value | 6.5~8.5 |
| Kinematic Viscosity (at 30℃, mm²/S) | 170~230 |
| Emulsion Stability (16~25% concentration) | Transparent liquid, no stratification within 3 days |
| Parameter | Value |
|---|---|
| Appearance (30℃) | Brown transparent liquid |
| Oil Content (%) | 99±1.0 |
| pH Value | 6.5~8.5 |
| Kinematic Viscosity (30℃, mm²/S) | 130~200 |
| Emulsion Stability (20%) | Transparent liquid, no stratification within 3 days |
| Parameter | Value |
|---|---|
| Appearance | Brown transparent liquid |
| Oil Content (%) | ≥98 |
| pH Value | 6.5~8.5 |
| Kinematic Viscosity (30℃, mm²/s) | 160~220 |
| Emulsion Stability (16~25% concentration) | Transparent liquid, no stratification within 3 days |
| Parameter | Value |
|---|---|
| Appearance | Yellow Transparent Liquid |
| Oil Content (%) | 90%±2% |
| PH Value | 6.5-8.5 |
| Kinematic Viscosity (30℃, mm²/s) | 50-80 |
| Emulsion Stability (6-16% concentration) | Transparent liquid, no delamination within 3 days |
| Parameter | Value |
|---|---|
| Appearance | Brown transparent liquid |
| Oil Content (%) | ≥98 |
| pH Value | 6.5~8.5 |
| Kinematic Viscosity (30℃, mm²/S) | 160~220 |
| Emulsion Stability (16~25% concentration) | Transparent liquid, no stratification within 3 days |
| Parameter | Value |
|---|---|
| Appearance | Brown transparent liquid |
| Oil Content (%) | ≥98 |
| pH Value | 6.5~8.5 |
| Kinematic Viscosity (30℃, mm²/s) | 160~220 |
| Emulsion Stability (16~25% concentration) | Transparent liquid, no stratification within 3 days |
| Parameter | Value |
|---|---|
| Appearance | Yellow transparent liquid |
| Oil Content (%) | 70±2 |
| pH Value (1% aqueous solution) | 6.5~8.0 |
| Kinematic Viscosity (30℃, mm²/S) | 18~26 |
| Parameter | Value |
|---|---|
| Appearance | Brown transparent liquid |
| Moisture (%) | ≤1 |
| Oil Content (%) | ≥99 |
| pH Value (1% aqueous solution) | 6.5~8.5 |
| Kinematic Viscosity (30℃, mm²/S) | 80~130 |
Polyester Industrial Yarn Finishes for HMLS and Safety Belt Yarn
Polyester industrial yarn is drawn hard and heat set, and a finish for it has to survive that without smoking off, gumming the heaters or letting the bundle spread. HMLS filaments shrink little and hold modulus through heat setting, so the finish there is chosen for heat stability and even film formation. Safety belt yarn is woven and treated afterwards, so the finish has to keep the yarn coherent through weaving. Denier, filament count and luster shift the balance between lubricity and cohesion.
SLT-2237 Polyester Industrial Yarn Spin Finish (HMLS) is suitable for the production process of polyester high-modulus low-shrinkage (HMLS) industrial filaments and serves as a special oil for HMLS filaments. SLT-2235 Polyester Industrial Yarn Spin Finish (Safety Belt) is the polyester industrial yarn spin finish for safety belts. Typical values for appearance, oil content, pH value, kinematic viscosity and emulsion stability are set out in the specification tables on this page.
The choice is a matter of the downstream article rather than the polymer alone. A line running HMLS for cord, hose or belting and a line running yarn for safety belts differ in draw ratio, heat set temperature and the treatments applied after weaving, and each puts different demands on lubricity and cohesion. Suretop adjusts formulations to the customer’s fiber type, spinning process and technical requirements. The wider polyester range is on the polyester spin finish page.
Nylon and Polyamide Industrial Yarn Finishes for Tire Cord and Airbag Yarn
A cord finish works on a yarn that will be drawn to high tenacity, heat set and then handled again in twisting, weaving and dipping. It has to keep friction low enough that filaments do not fray against guides at speed, hold the bundle together so the twist builds evenly, and carry static away so the package does not balloon. It also has to leave the surface in a state where downstream treatments can act on the yarn. Airbag yarn takes a different downstream route, so the finish is chosen for that route.
- SLT-60 Industrial Yarn Spin Finish for Nylon Cord (Tire Cord), for nylon 66 tire cord on high-speed lines
- SLT-80 Polyamide Industrial Yarn Spin Finish for Nylon 66 (High-Strength Yarn), for nylon 66 high-strength yarn
- SLT-101 Polyamide Industrial Yarn Oil (High-Strength Yarn)
- SLT-70 Polyamide Industrial Yarn Spin Finish (Airbag Yarn), for polyamide 66 airbag yarns
- SLT-100 Nylon Industrial Yarn Oil, the oiling agent for nylon 6 crude oil
- SLT-AZ-60 Special Tire Cord Fibre Spin Finish Oil
Nylon 66 Tire Cord Oil SLT-60 is compounded with synthetic esters, surfactants, antistatic agents and special additives. On the yarn it gives good antistatic property, good bundling performance, good dyeing performance and good heat resistance. Nylon High-Strength FDY Oil SLT-80 is compounded with synthetic esters, surfactants, antistatic agents and special additives. SLT-101 Oil for Nylon 6 Crude Oil Impregnation and Nylon 6 Crude Oil Oiling Agent SLT-100 are each compounded with synthetic esters, antistatic agents and special additives. Table values are given in the specification tables on this page.
Formulations can be adjusted to the customer’s fiber type and spinning process, and samples are available for testing and trial production. Send the cord yarn specifications through the inquiry form — denier, filament count, tenacity target, draw ratio and the downstream treatment — and Suretop will confirm the grade and the application rate. The nylon range is described on the nylon spin finish page.
Matching Fiber, Process and Downstream Use Before a Trial Run
Finish selection follows the fiber first: polyester, nylon, spandex and aramid each wet out and lubricate differently, and within a polymer the denier, the filament count, the luster and the spin speed change how much lubricity and cohesion the yarn needs. The step after spinning matters as well, because a yarn that is drawn, heat set and dipped behaves differently from a yarn that goes to texturing or coning. General principles are covered in what is a spin finish.
Suretop has an R&D team that works with several Chinese universities and draws on spin finish technology from Japan and Germany, and the company offers OEM/ODM supply. A dynamic yarn tension testing instrument developed by Lawson-Hemphill (USA) analyses the properties of the finish on the yarn, which helps when a formulation is adjusted for a particular spinning condition.
- Send the fiber type, the spinning process, the yarn denier and the equipment in use
- Receive a recommended grade and an application rate for those spinning conditions
- Test a sample on the line, then run trial production
- Confirm the order, packaging and delivery schedule
- Receive the finish in 200 L or 1,000 L drums
The MOQ is 200 kg for most Suretop spin finishes, confirmed for the selected product and order. The average lead time is within 15 working days in peak and off season. Actual delivery time is arranged according to order quantity, packaging requirements and destination. Payment is by T/T or L/C, quotations are on FOB, EXW, CFR or CIF terms, and shipping is by sea, air or express, and the nearest ports are Shanghai Port and Ningbo Port. Main markets are Eastern Asia, the Middle East, Southeast Asia and Africa.
How an order runs
- Send your process details
- Fiber type, process (POY, FDY, DTY or industrial yarn), denier and luster, and the spinning equipment you run.
- Finish recommendation
- Suretop proposes a matching finish, or adjusts a formulation to your fiber type and spinning process.
- Sample and trial
- Samples are supplied for testing and trial production, with a recommended application rate for your conditions.
- Order terms
- Payment by T/T or L/C; FOB, EXW, CFR or CIF terms; transport package in 200 L or 1,000 L drums.
- Delivery
- Delivery time is arranged according to order quantity, packaging requirements and destination.
Request a quotation
Describe your fiber, process and equipment, and we will suggest a model and a sample.
Or write to sales@spinfinishoil.com